Diagnosing HVAC Issues That May Cause Compressor Overload With Your Heating And AC Repair Company | Fort Worth, TX
A smoothly operating HVAC system is necessary for your Fort Worth, TX home’s continued comfort, especially in the extreme temperature seasons. One of the most recommended practices to ensure that the unit is optimally operating is to ensure that a heating and AC repair company sends a technician over for routine maintenance. Since you lean too heavily on your heating and air conditioning system, you risk overworking the unit without regular inspection and timely maintenance. Unfortunately, this could potentially result in compressor overload. Overloads usually happen when the compressor overheats and eventually shuts down your entire system. Below are some of the most common problems that could result in a heating and air conditioning system compressor overload.
Obstructed Condenser Coils
The condenser is one of the most critical components of a heating and air conditioning system. These coils play a vital role in the dissipation of heat. Hence, any problem with the condenser coils could result in serious issues in your HVAC system. They are usually located within the outdoor component of the air conditioning system, which is susceptible to the accumulation of debris such as grass, leaves, and other outdoor pollutants.
An accumulation of these elements on the condenser coils will block the airflow over them. Hence, the heat will not be dissipated as efficiently as possible. Thus, the compressor will run extensively, overloading them because of overheating. Fortunately, you can avert this problem by enlisting the help of a heating and AC repair company for routine maintenance.
Overheating the compressor might result in other damages that may result in costly heating and AC repairs. Further, obstruction of the condenser coils results in a reduction of the efficiency of the system. Hence, you might notice that your energy bills are increasing. You should ensure the condenser is cleaned when the heating and AC repair company sends someone for a maintenance visit. This should be done regularly. The professional may also clear the area around the condenser to ensure no obstructions.
Routine maintenance is essential to ensure that the condenser coils are unobstructed. This also will prolong the life of your HVAC system as it will not be straining to heat or cool your Fort Worth, TX home. By ensuring that the coils are clean and the area surrounding the condenser is clear, you will have dealt with one of the most notorious causes of compressor overloads. Additionally, ensure that a heating and AC repair company sends a professional for routine maintenance. This will keep your HVAC system operating efficiently for most of the year.
Dirty Components
The other common reason your compressor might be overloaded is that some HVAC components need to be cleaned. Over time, dirt, dust, and other debris may accumulate on various HVAC systems components, such as the evaporator coils, air ducts, and air filters. Such dirty components may restrict air flow, meaning the compressor will have to work hard or even potentially overheat. The accumulation of dirt on filters and ducts will also reduce the efficiency of the HVAC system and negatively impact indoor air quality. This might also increase energy costs. Routine maintenance of your HVAC system by a reliable heating and AC repair company is critical in ensuring that your system runs optimally. This will prevent compressor overloads and ensure that your system serves you longer.
Unfortunately, dirty air filters are among the leading causes of restricted airflow in your HVAC system. The filters are solely responsible for eliminating airborne contaminants such as pollen, dirt, and dust, among other pollutants, before they are circulated into your indoor space. If the filters become clogged, the compressor is forced to work harder when pumping the refrigerant to compensate for the air not flowing into your Fort Worth, TX home. Additionally, the accumulation of debris and dirt on the evaporator coils may also harm the efficiency of your HVAC system. Hence, the compressor has difficulty pimping the refrigerant to cool the air.
It’s crucial to change the air filters frequently and have the system expertly cleaned to avoid this. Depending on usage and the surrounding conditions, air filters should be changed at least once every month. To make sure that all components are clean and in good functioning order, it is also advised to have a heating and AC repair company in Fort Worth, TX. Inspect and service the HVAC system every year or every two years. By doing this, you can ensure that the system operates as efficiently as possible and that the compressor is safeguarded against overload.
A Faulty Thermostat
Another essential component of your HVAC system is the thermostat. It controls the indoor temperatures of your Fort Worth, TX home. It acts as the brains for your unit. The thermostat monitors the temperatures and sends signals to the compressor to turn off or on depending on the temperature values you’ve set. However, if your thermostat is faulty, it might make the compressor run repeatedly for too long. This will place an extra strain on the HVAC system, potentially making it overloaded. Have you noticed or suspected that the thermostat in your air conditioner is faulty? Have it inspected by a professional, licensed heating and AC repair company.
If the thermostat is malfunctioning, it will make the system frequently short cycle (turn on or off). This will place an extra strain on the HVAC system. Unfortunately, the short cycling compressor will make it overheat and potentially fail. Short cycling also results in reduced energy efficiency in your system and a higher energy utility cost. However, a heating and AC repair company can come for regular thermostat inspection and calibration.
The heating and AC repair company will check the thermostat for proper operation and calibrate it to ensure that it can send signals to the HVAC without a problem. They also will check for any physical or electronic issues, if any. If the thermostat is not repairable, the technician will replace it with a new one. They recommend that you install a programmable, smart, or WIFI thermostat. However, there are better ways to go than calling the pro whenever you notice a problem. You should have a reliable, licensed heating and AC repair company send a technician to come over for routine maintenance of your HVAC system and thermostat.
Insufficient Refrigerant
The other notorious cause of HVAC compressor overloads can be because of low levels of refrigerant. The refrigerant is a critical component of an HVAC system responsible for heat transfer. It removes the heat from the air before it enters your Fort Worth, TX home to ensure that you have a comfortably cooled home. The compressor will have difficulty cooling the air if there’s insufficient coolant on your HVAC system. This may make it become overloaded or even fail. This is one of the problems that a heating and AC repair company will diagnose when they come for a maintenance visit.
The low refrigerant levels may be caused by various factors such as improper installation, leaks in the HVAC system, and undercharging. Wear and tear, corrosion, or damage to the suction line are the main reasons these leaks might arise. It would be best if you had a technician inspect the refrigerant levels when they come for a maintenance visit. If there are leaks, the heating and AC repair company will seal the leaks and recharge the refrigerant to the recommended levels. Remember, overcharging the AC also has its problems.
These technicians are professionally trained and equipped to check the system for leaks and make the required repairs. Their maintenance service ensures that your unit can serve you longer and that the refrigerant is always at the recommended levels. However, you must hire a licensed heating and AC repair company to handle refrigerant leaks. This is because the refrigerant is toxic, and there are some aspects that only they know. These include the type of refrigerant and the recommended refill level.
Oversized Unit
Compressor overload is one issue arising from an HVAC system that is too big for the area it is intended to cool. The compressor, which compresses and circulates the refrigerant throughout the device, is an essential part of the HVAC system. An oversized unit will regularly cycle on and off, putting additional strain on the compressor. This could shorten the compressor’s lifespan and perhaps result in its failure because of increased wear and tear on the device. Ask a trustworthy heating and AC repair company for appropriate HVAC sizing to ensure your compressor isn’t overworked.
Short cycling is another issue brought about by excessive units. Short cycling occurs when a device cycles on and off too frequently without giving the compressor enough time to warm up to the proper working temperature. This may cause the compressor to overheat, harming it and lowering its effectiveness. An oversized unit might also result in high energy expenses since the system runs more frequently than necessary, using more energy and raising utility costs. Have you recently noticed this? Have a certified heating and AC repair company examine your heating and cooling system.
The system must be appropriately sized for the area it is intended to cool. A load assessment can be done by a qualified heating and AC repair company to ascertain the right size unit for the room and make any necessary modifications. This load estimate considers elements including the size of the room, the number of people, the unit’s location, and the level of comfort sought. By correctly sizing the unit, the HVAC system can operate more effectively, putting less stress on the compressor and resulting in lower energy expenditures.
HVAC Doesn’t Receive Enough Electricity
Compressor overloads in your HVAC system can also severely impact the system’s functioning, the overall cost of running the system, and the energy efficiency of your HVAC system. A lack of electrical power in your HVAC system could overload the compressor. If your HVAC system doesn’t receive enough electrical power, the compressor might struggle to run or start at a lower capacity.
There are several probable causes of the lack of electrical power in your HVAC system. For instance, a tripped breaker could prevent the system from getting the required power. Damaged wiring and a bad capacitor could also make your HVAC system malfunction resulting in a lack of electricity. This could be caused by various factors, such as natural disasters, power surges, or even wear and tear. While routine maintenance by a heating and AC repair company in Fort Worth, TX may not address some of these issues, it is critical to ensure the system’s efficient functioning.
Compressor overloads can be avoided by having an experienced heating and AC repair company evaluate the electrical components of the air conditioner. This can be a beneficial measure. The expert will check to ensure sufficient electrical service to the unit and that the system is wired correctly. During a maintenance visit, a trained professional will effectively address issues such as tripped breakers and malfunctioning relays appropriately.
Besides preventing compressor overloads, routine maintenance and repairs can also improve HVAC efficiency and lower energy costs. If you take the time to ensure that the system is operating as it should, you may cut down on the energy required to keep it running, saving you money in the long run. Engage the services of your go-to heating and AC repair company for HVAC maintenance on an annual or semi-annual basis.
Contact Us for a Routine Maintenance of Your HVAC
Compressor overloads can cause many different issues. Hence, it is critical that you leave nothing to chance when it comes to ensuring that this particular problem is averted. While your compressor may be overloaded for many reasons, routine maintenance of your heating and air conditioning system will deal with most. Contact us at One Hour Air Conditioning & Heating of Fort Worth today for an inspection and yearly tune-ups that ensures your unit remains optimally functional.